Take a seat

I just got my seat back from Jesse at Jesse's Plastic Covers in brooklyn ny, if you looking for a quality seat in bk hit him up.

and right after making it look pretty, i tore it down again.

Rear sets

looks like my rear sets mounts finally came in the mail!!

I didn't have a torch hot enough that could bend the 3/4 rod, so i made a trip to Kieno's shop and borrowed his oxy acetylene torch for about 20secs. So nice. It was exciting and i took photos for everyone, but then keino let me take his '47 750 flathead out for a quick rip. and i figured a shot of that bike would be a better use of your eyes time. Such a fun ride.

back to my shop, welded up the entire rear set mounts, and getting ready to attach it to the frame.

HIGH AND TIGHT! the way a cafe bike should be. looks like ill be doing some stretching before any rides on this beast.

I earned my keep. and celebrated with a lot beers and tequila.

Olde Pro stopped by

At this exact moment, I realized i could have just bought a Buell and be done with it, but that would have been lame - so fuck that. Carry on!

And a quick thanks to all the rad companies that are supporting the Greasy Dozen

www.Biltwell.com @biltwell


www.burlybrand.com @burlybrand


www.chopcult.com @chopcult


www.indianlarrymotorcycles.com @indianlarrymotorcycles


www.kickstartcycle.com @kickstartcycle


www.kundratickustoms.com/ @kundratickutoms


www.ledsledscustoms.com @ledsledcustoms


www.LowbrowCustoms.com @lowbrowcustoms


www.lowsidesyn.com/ @lowside_magazine


www.mooresensible.com/


www.digthelid.com/ @oldschoolhelmets


www.oldbikbarn.com @oldbikebarn


www.Rockandride.com @rockanride


www.showclassmag.com/ @show_class_mag


http://www.speeddealercustoms.com/ @speeddealer


www.spitfiremotorcycles.com @spitfiremotorcycles


www.sscycles.com @spitfiremotorcycles


www.tcbros.com @tcbroschoppers


www.triplesixcrewdeathco.com @triplesixcrewdeathcompany


www.paisanopub.com/wrench/ @wrenchmagazine

Oil routing

Hey look - Black Pipes! 

Like I said, I'm not a huge fan of the matte, so I'll have to find a gloss high temp paint to make this something I can get behind. 

But this post is about the sweet oil lines. they are so hard.

Got the lines all bend in to shape.

I realized after doing this, that there is also a vent hose for the primary, and I can't have three hard lines and one rubber, so i ended up having to bend up one more. 

But before all that, I decided it was time to see if my sprained ankle was well enough to get back on the foot clutch. It was! 

After all that fun, I started to make guides for the hard lines. 

I still need to clean up the guides and weld tabs to them and the frame then they will be mounted in place.

Took a paint break

Decided chrome pipes was to obvious. 

Got these fuckers ready to go black. 

- they ended up matte black, which i don't like. I'm gonna have to try and find a gloss high temp paint.

okay this was the real break i was talking about. I told a friend i would do this forever-ago, finally got it done. 

Also helped out my buddy Myles with his pan on some frame painting. We bought nail polish on advice from the internet - don't do it. nail polish on powder coat is a bad idea and doesn't work because of the alcohol in the paint. thanks again internet and your 'wealth' of knowledge, we ended up using some oneshot. 

Stripping

i started to lay out tape guides for stripping, two thin pin stripes one red one white down the center. 

and after i painted them in, i hated it. absolutely hated it.

so i took a different approach. 

Anubis took over, and when i came though my tanks looked good.

After laying down the gold, i realized that i didnt follow the base line of the gas tank, which i intentally aligned with the crease in the oil tank. So i had to fix that. 

A bit of sanding and more stripping later. 

Seat foamin

Not the best foam job, but it will do the trick. its three layers of a thick yoga mat and one layer of race foam, donated by a kind fella over at Team Obsolete, i guess they were fans that I'm adding a kicker pedal, and removing the electric starter to this modern bike.

Ready for its new skin

time is running out. gotta get this seat pan ready for its new skin. 

added a rear lip to help connect it with the oil tank

shameless tig shot, as well as holes drilled for the rivets 

the oil tank isn't fixed in place yet, hopefully that gap can be cleaned up a bit. 

current thought on how the skin will look. 

Painting not my bike

I need to stop saying yes to friends. I haven't spent much time working on my build. I have been helping a buddy by painting his tanks and fender for his shovel. Still need to finish the fender and clear.